S9200U1000 Honeywell Universal Hot Surface Igntion Integrated Furnace Control. Controls a standard induction-type circulating fan motor. ALL ITEMS ARE BRAND NEW AND IN FACTORY SEALED CARTON WITH INSTRUCTIONS IF APPLICABLE. The S9200U1000 can be used with conventional thermostats as well as the EnviraCOM™ enabled VisionPRO IAQ and FocusPRO. The S9200U1000 Universal Integrated Furnace Control is intended for residential natural or liquid propane fueled furnaces only. The S9200U1000 EnvriaCOM™ communications capability allows its use in twinning applications and enables communication with local and remote diagnostic devices such as the QuickLook hand held device (QuickLook™ 72), EnviraLNK® web-based application and the W8735D Telephone Access Module (TAM). • Main burner ignition using a 120V hot surface igniter. • Flame rectification circuit to monitor flame presence. • Monitoring of system pressure switch, high temperature limit, and rollout functions. • Appliance operation/safety requirements controlled via microprocessor. • Control of a standard induction-type circulating fan motor (based on appliance requirements), in response to a conventional low voltage or EnviraCOM™ thermostat. • LED system status, performance and diagnostic indication. • Wire harnesses provided for simple replacement of most IFCs and integration with most heating and cooling appliances. • EnviraCOM™ communication capability to enable local and/or remote system status, diagnostics, troubleshooting, and HVAC system control. Product Specifications Back To Top Description Universal single stage heating & cooling Line Voltage 120Vac (97-132 Vac) Operating Temperature (F) -40 F to +175 F Operating Temperature (C) -40 C to +79 C Operating Humidity Range (% RH) 0% to 95% non-condensing Igniter Current 1.0A resistive @ 95Vac output Thermostat Anticipator Setting (Stage 1 only) 100mA HSI Warmup Time 17/27 or 30/30 seconds Trial For Ignition 4, 6, or 8 seconds Ignition Trials Three, two tries if flame is not sensed Flame Failure Response Time 2 Seconds max @ 1µA Heat On Fan Delay 30 or 60 seconds Heat Off Fan Delay 60, 90, 120, or 180 Seconds Cool Fan Off Delay 0 or 60 seconds Gas Control Used With Any 24Vac redundant, direct ignition gas control rated at 1.5A or less. Honeywell VR8205 recommended. Cooling Contactor Used With Any 24Vac contactor rated at 1.0A or less Induced Draft Blower Load 2.2FLA / 25LRA max @120Vac Ciculator Load 14.5FLA / 25LRA max @120Vac Type of Fan Used With Standard Induction-Type Circulating Fan S9200U1000 Universal Integrated Furnace Control Cross-Reference Guide 903106- 50024568: Main Connector & 50024565 Inducer & HSI Connector CAR33101972200 -50024568: Main Connector & 50024566 Inducer & HSI Connector CAR50A55843 CARB1809913S- 50026393: Main Connector & 50026446 Inducer & HSI Connector 1809913- 50026393: Main Connector & 50026446 Inducer & HSI Connector PSIB18099-13PSI- No wiring harness required ICM CONTROLS WIRING HARNESS USED ICM280- 50026393: Main Connector & 50026446 Inducer & HSI Connector G951ADB1401- 50024568: Main Connector & 50024566 Inducer & HSI Connector 624557- 50024568: Main Connector & 50024565 Inducer & HSI Connector PSI903106PSI- No wiring harness required 3100662000- 50024568: Main Connector & 50024566 Inducer & HSI Connector RHEEM / RUUD WIRING HARNESS USED 62-24268-01- 50024568: Main Connector & 50024566 Inducer & HSI Connector TEXAS INSTRUMENTS WIRING HARNESS USED 6DT-1- 50024568: Main Connector & 50024566 Inducer & HSI Connector 41F-5- 50026393: Main Connector & 50026446 Inducer & HSI Connector WHITE-RODGERS WIRING HARNESS USED 50A50-209- 50024568: Main Connector & 50024566 Inducer & HSI Connector 50T35730- 50026393: Main Connector & 50026446 Inducer & HSI Connector 50A55-843- No wiring harness required 1012-925A- 50024568: Main Connector & 50024566 Inducer & HSI Connector 1012-955A- 50024568: Main Connector & 50024565 Inducer & HSI Connector 1012-83-9651B- 50024568: Main Connector & 50024566 Inducer & HSI Connector 1012-930- 50026393: Main Connector & 50026446 Inducer & HSI Connector (We do not proofread any ads submitted by members) |
ora_burks@desmoines-classifieds.com (Ora Burks)
for more information. Your emails will be instantly forwarded to the poster's private address.