|
SIMCO XP-20 AEROSTAT ELIMINATION IONIZING BLOWER WITH SIMCO N167 STATIC ELIMINATOR POWER UNIT (040605506040) This does not mean that the unit doesn’t work, only that we have not tested or checked it out. This may also mean that we are not knowledgeable in that specific item. Please call MONIQUE Toll Free at 1-866-MHZ-ELEC (1-(***)-649-3532) if you have questions between the hours of 9:00 AM and 4:00 PM Monday thru Friday Pacific Time. The Item may vary from picture as manufacture may change model appearance. All information, including description, specifications and features are from a manufacturers data sheet or manual and are subject to change without notice. Meaning that all information included in the description, specifications and features What you see is what you get! If it doesn’t show it you probably won’t get it! Simco XP-20 Aerostat Static Elimination Ionizing Blower with Simco N167 Static Eliminator Power Unit * XP-20 Serial Number: W17051 * XP-20 Electrical Requirements: 120 Volts AC, 60 Hz, 1.9 Amps * XP-20 Operating Voltage: 7kv RMS – 9kv RMS Maximum * XP-20 Retail Price: $1,640.00 * N167 Serial Number: W279225 * N167 Input: 120 Volts AC, 0.24 Amps, 60 Hz * N167 Output: 7kv RMS, 3ma Max, 5ma SCC Max. * N167 Retail Price: $428.00 XP-20 Static Elimination Ionizing Blower General Description: * The XP-20 Static Control Blower is approved for use in Class I, Division 1 and 2, Group D hazardous areas. This is the only blower available on the market with UL approval for use in hazardous areas. * UL Listed for Class I, Division 1 and 2, Group D hazardous areas * Designed for rugged industrial use * Powerful air blast at 285 CFM * Replaceable air intake filter * Power Requirements: 120 Volts AC, 60 Hz, 1.9 Amps * Size:17 ¾†in. W x 9†in. H x 16 ¾†in. D * Area Volume Output: Fixed; 285 CFM * Effective Coverage: 2’ x 10’ area * Discharge Time (5000V to 500V at 1: .9 seconds * Integrated Power Supply: No * Built-in Emitter Point Cleaner: No * Approved for Class I, Division 1, Group D Hazardous Locations: Yes N167 Static Eliminator Power Unit General Description: * The N167 is Simco's most versatile power supplies. They can be used with the ES2A4 Ionizing Air Gun and several shockless static bar models (ME100, MEB, MEJ, PLS and MEC). A terminal block connector inside the power supply allows for the connection of up to four static eliminators to one power supply. The unit accepts either shielded or unshielded cable. * The N167 has the added benefit of being FM approved for use in Class I, Division 1 and 2, Group D hazardous areas for electrostatic finishing applications involving spray painting, dipping, coating, and liquid printing. The power supplies must be installed outside of the hazardous area and be used to power an XP-20F Blowers or XP-2 Static Bars located inside the hazardous location. The connecting high voltage cable must be run through rigid or flexible metal conduit sealed at each end. * The N167 is designed with short circuit protection (no fuse required!) which protects the power supply in the event of a short in the static eliminator or cable. * Input Requirements: 120 Volts AC, 60 Hz * Output Voltage: 7 kV, 3mA max * Number Of Outputs For Static Eliminators: 4 * Max Length Of Static Bars Which Can Be Attached: 300 inches * Does The Unit Accept Shielded Cable: Yes * Acceptable For Hazardous Locations: See description (We do not proofread any ads submitted by members) |
J-horton@desmoines-classifieds.com (Jannie Horton) for more information. Your emails will be instantly forwarded to the poster's private address.
