Dual Power USB Willem Programmer PCB5.0 Built-in PLCC32 & FWH /LPC Adapter * Programmer hardware design is based on Willem Programmer * Programming speed 3 times faster than PCB3x & PCB4.xxx * Bulit-in PLCC 32 & FWH LPC adapter * Jumper selectable for 3V or 5V chips - eg. 39SF020, 39VF020, 29F320 & 29LV320 * Jumper seclectable for VPP 12.5V & 21V * Use PC USB Port or 12V AC/DC power adapter as power source 1. Dual Power USB Willem Programmer PCB5.0 2. Programmer Latest software and manual on CD Rom 3. USB & Parallel Printer Cable Denmark, Finland, Norway, Sweden & Switzerland by Registered Airmail Registered / Recorded Airmail ( Addressee signature required) with Bar code number 27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040,27C1001 2764, 27128, 27256, 27512, 27010, 28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040 (Adapter or Jumper) 28C16,XLS2816 (DIP24) 28F64, 28F128, 28F256, 28F512,28F010, 28F020 MX26C1000, MX26C2000, MX28F1000, MX28F2000 Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command erase/prog.) i28F001BX, 28F004, 28F008, 28F016 29F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040, 29F080 29F001,29F002, 29F004, 29F008, 29F016, 29F032 24C02,24C04,24C08,24C16, 85C72, 85C82, 85C92 24C32,24C64,24C128,24C256,24C512 <- Data 8bit -> (pin 6 ->ORG. [Schematic connect to GND]) 93C06, 93C46, 93LC46, 93C56, 93C57, 93C66, 93C76, 93C86 (8bit), AT59C11, AT59C22, AT59C13 CAT35C102, CAT35C104, CAT35C108 (pullup pin7) <-Data 16bit-> (pin 6 ->NC [No Connect]) 93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS) 16C84, 16F84, 16F84A ,16F627/16F628 12C508/A, 12C509/A, 12CE518, 12CE519, 16C505 16C620 16C621, 16C622, 16CE623, 16CE624, 16CE625, 16C710/711 16F870, 16F871, 16F872, 16F873, 16F874, 16F876, 16F877 PIC16F873A, PIC16F874A, PIC16F876A, PIC16F877A AT29C256, AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040A W29EE512,W29EE011, W29EE012, W29C020(128),W29C040 ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020) Ver 0.992 up(DOS). Can run under win9x (disable prog. CPUIdle or CPUCool) Command seq. 5555/AA, 2AAA/55, 5555/A0 AT49F512, AT49F010, AT49F020, AT49F040 SST39SF010, SST3S9F020 ,SST39SF040 Command seq. 555/AA, 2AA/55, 555/A0 Am29F512, Am29F010, Am29F020, Am29F040,HY29F080 Serial Peripheral Interface (SPI) [Atmel] AT25010,020, 040 (A8-A0) AT25080, 160, 320, 640, 128, 256 (A15-A0) [ST] W95010....256, Microchip 25x010 - 25x640 25C080,25C160,25C320,25C640,25C128,25C256,25C512 - CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx CAT64LC010, CAT64LC020, CAT64LC040 DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB 6116, 6264, 62256, 62512, 628128 W27E512, W27E010, W27C010, W27C020, W27C040 SST27SF256, SST27SF512, SST27SF010, SST27SF020 Vcc = 3.3-3.6V SST37VF512, SST37VF010, SST37VF020, SST37VF040 AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53 AT89C1051,AT89C2051,AT89C4051 (20pin) AT89C51RC (32KB), AT89C55WD (6.2V) i8xC51,i8xC52,i8xC54,i8xC58 (tWP = 100uS*25 Pulse) (read,write,erase,verify,checkempty,Lockbits ,Fusebits) [Flash memory/EEPROM] Function Lockbit read AT90S2313 Errata Sheet.pdf P8048AH, P8049AH,P8050AH, P8042AH Vea = 12V D8748,D8749,D8742,D8741, D8742 Vea = 18V Am29F400,Am29F800,29F160,29F320 (read,write byte mode) HY29F200, HY29F400, HY29F800 , AT49F2048A, AT49F4096A, AT49F8192A i28F200,i28F400,i28F800,i28F160 (TSOP48) 27C1024 (27C210), 27C2048 (27C2002), 27C4096 (27C4002), by use Resister pull up Data Bus (0xFF), A0 select low or high byte) EPROM 16bit (DIP42) (4-32Mbit) M27C400(DIP40), 27C800, 27C160, 27C322 by use Resister pull up Data Bus (0xFF), A0 select low or high byte) 29LV200, 29LV400,29LV800,29LV160,29LV320 (read,write byte mode) Adapter Firmware Hub/LPC (PLCC32) (PP mode) (3.3V) 82802AB, 82802AC, AT49LW040, AT49LW080 SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A (We do not proofread any ads submitted by members) |
Kristina_maxwell@desmoines-classifieds.com (Kristina Maxwell)
for more information. Your emails will be instantly forwarded to the poster's private address.